Hard drives and mounting - zfs and ext2 - PC-BSD Forums

nagatzul · #1 12-26-2010, 08:21 PM

Hi

I'm new to BSD (previously gentoo) and am trying to get my drives mounted.

Code:

egrep 'ad[0-9]|da[0-9]' /var/run/dmesg.boot

gives me

Code:

atapci2: <Intel ICH9 SATA300 controller> port 0xd600-0xd607,0xd700-0xd703,0xd800-0xd807,0xd900-0xd903,0xda00-0xda0f,0xdb00-0xdb0f irq 19 at device 31.2 on pci0
ad10: 953868MB <Seagate ST31000528AS CC34> at ata5-master UDMA100 SATA 3Gb/s
ada0 at ahcich1 bus 0 scbus1 target 0 lun 0
ada0: <ST3500630AS 3.AAK> ATA-7 SATA 1.x device
ada0: 150.000MB/s transfers (SATA 1.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 476938MB (976771055 512 byte sectors: 16H 63S/T 16383C)
ad11: 476938MB <Seagate ST3500320AS SD15> at ata5-slave UDMA100 SATA 1.5Gb/s
ad12: 1907728MB <Seagate ST32000542AS CC34> at ata6-master UDMA100 SATA 3Gb/s
ad13: 1430799MB <Seagate ST31500341AS CC1H> at ata6-slave UDMA100 SATA 3Gb/s
da0 at umass-sim0 bus 0 scbus4 target 0 lun 0
da0: <Seagate FA GoFlex Desk 0155> Fixed Direct Access SCSI-4 device 
da0: 40.000MB/s transfers
da0: 2861588MB (732566645 4096 byte sectors: 255H 63S/T 45600C)
da1 at umass-sim1 bus 1 scbus5 target 0 lun 0
da1: <Seagate FA GoFlex Desk 0155> Fixed Direct Access SCSI-4 device 
da1: 40.000MB/s transfers
da1: 2861588MB (732566645 4096 byte sectors: 255H 63S/T 45600C)
da2 at umass-sim2 bus 2 scbus6 target 0 lun 0
da2: <Seagate FreeAgentDesktop 100D> Fixed Direct Access SCSI-4 device 
da2: 40.000MB/s transfers
da2: 476940MB (976773168 512 byte sectors: 255H 63S/T 60801C)
da3 at umass-sim3 bus 3 scbus7 target 0 lun 0
da3: <Seagate FreeAgent XTreme 4113> Fixed Direct Access SCSI-4 device 
da3: 40.000MB/s transfers
da3: 1430799MB (2930277168 512 byte sectors: 255H 63S/T 182401C)

Two drives are zfs and the rest are ext2.

I have no trouble mounting my pools but have trouble getting my old linux disks mounted.

Code:

mount -t ext2fs /dev/da0 /media/1
mount: /dev/da0 : Invalid argument

Am I missing something here?

Help much appreciated.

nagatzul · #2 12-27-2010, 08:27 AM

Code:

 mount -t ext2fs /dev/da3s1 /media/1
mount: /dev/da3s1 : Invalid argument

ext2fs is loaded as kdload says file is already there.

Please help.

nagatzul · #3 12-27-2010, 11:41 AM

It seems mount_ext2fs gives me a command not found.

How would I go about enabling this?

nagatzul · #4 12-30-2010, 01:45 PM

Eventually just copied everything in Gentoo, with zfs-fuse.